Volume 5, Issue 3, September 2020, Page: 82-87
A Comprehensive Prediction Model of Rock Strength and Its Application on Classifying the Rock During the Drilling
Lu Yang, School of information and Control Engineering, China University of Mining and Technology, Xuzhou, China
Yinan Guo, School of information and Control Engineering, China University of Mining and Technology, Xuzhou, China
Cancan Liu, School of Mines, Key Laboratory of Deep Coal Resource Mining, Ministry of Education of China, China University of Mining and Technology, Xuzhou, China
Received: Sep. 10, 2020;       Accepted: Sep. 21, 2020;       Published: Sep. 29, 2020
DOI: 10.11648/j.aas.20200503.15      View  35      Downloads  18
Abstract
Geological data plays an indispensable role in mining coal safely and efficiently. Traditional rock core method not only have some defects of high labor intensity, high cost and slow speed, but also difficultly got the rock of the weak interlayer. Based on this, parameter-based identification method of the rock characteristics during the drilling operation is a hot research topic. In this paper, a comprehensive prediction model was established to predict the rock Uniaxial Compressive Strength (UCS). Besides, the prediction results of the comprehensive prediction method, multiple linear regression model, and Mechanical Specific Energy (MSE) model were compared. Furthermore, the K-means clustering method is used to classify the rock formation based on the measured drilling parameters. The result indicates that torque work is significantly correlated with the UCS of rock. The comprehensive method has the best prediction result, and the prediction error of rock's UCS is within 5MPa. The prediction results of rock classification are different from the actual results, but from the perspective of rock strength, this classification method is better. The rapid identification method of rock formation based on MWD provides a reference for the roadway support scheme and parameter design, and is an important part of the intelligent development of coal mines.
Keywords
Measurement While Drilling, Parameters While Drilling, Rock Classification, Support Parameter, Uniaxial Compressive Strength
To cite this article
Lu Yang, Yinan Guo, Cancan Liu, A Comprehensive Prediction Model of Rock Strength and Its Application on Classifying the Rock During the Drilling, Advances in Applied Sciences. Vol. 5, No. 3, 2020, pp. 82-87. doi: 10.11648/j.aas.20200503.15
Copyright
Copyright © 2020 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
Tian, J., J. Li, W. Cheng, Z. Zhu., L. Yang., Y. Yang., T. Zhang. (2018). Working mechanism and rock-breaking characteristics of coring drill bit. Journal of Petroleum Science & Engineering. 162: 348-357.
[2]
Galdames, F. J., Perez, C. A., Estévez, P. A., Adams, M. (2017). Classification of rock lithology by laser range 3D and colour images. Estévez, et al. Rock Lithological Classification by Laser Range 3D and Color Images [J]. International Journal of Mineral Processing. 160, 47-57.
[3]
Zhao, J., and Yu, j. (2017). Exploration on nonlinear geo-electrical structures to detect coal mine goafs using three-dimensional borehole resistivity imaging discrete approach, Journal of difference equations and applications. 23 (1-2), 312-321.
[4]
Liu, C., X. Zheng, G. Wang, M. Xu, Z. Li. (2020). Research on drilling response characteristics of two-wing PDC bit. Sustainability, 12 (1), 406.
[5]
Vardhan H, Adhikari G R, Raj M G. (2009). Estimating rock properties using sound levels produced during drilling. International Journal of Rock Mechanics & Mining Sences. 46 (3): 604-612.
[6]
Vardhan, H, Murthy C S N. (2007). An experimental investigation of jack hammer drill noise with special emphasis on drilling in rocks of different compressive strengths. Noise Control Engineering Journal. 55 (3): 282-293.
[7]
Yasar, E., Ranjith, P. G., and Viete, D. R. (2011). An experimental investigation into the drilling and physico-mechanical properties of a rock-like brittle material. Journal of Petroleum Science & Engineering. 76 (3-4), 185-193.
[8]
Rodgers, M., Mcvay, M., Horhota, D., et al. (2018). Assessment of rock strength from measuring while drilling shafts in Florida limestone. Canadian Geological Journal. 55,1154-1167.
[9]
Teale, R. (1965). The concept of specific energy in rock drilling. International Journal of Rock Mechanics & Mining Sciences & Geomechanics Abstracts. 2 (1), 57–73.
[10]
Dupriest, F. E., W. L. Koederitz. Maximizing drill rates with real-time surveillance of mechanical specific energy. In: SPE/IADC Drilling Conference. Society of Petroleum Engineers 2005.
[11]
Cherif, H., S. Bits. FEA modelled MSE/UCS values optimise PDC design for entire hole section. In: In at the North Africa Technical Conference and Exhibition Held in Cairo, Egypt, 20e22 February 2012.
[12]
Chen, X., D. Gao, B. Guo, Y. Feng. (2016). Real-time optimization of drilling parameters based on mechanical specific energy for rotating drilling with positive displacement motor in the hard formation. Journal of Natural Gas Science and Engineering. 35, 686–694.
[13]
Al-Sudani, Jalal, A. (2017). Real-time monitoring of mechanical specific energy and bit wear using control engineering systems. Journal of Petroleum Science & Engineering. 149, 171–182.
[14]
Wang, Q., Q. Qin, S. Gao, S. Li, and H. Gao. (2018). Relationship between rock drilling parameters and rock uniaxial compressive strength based on energy analysis. Journal of China Coal Society. 43 (5), 1289-1295.
[15]
Liu, W., Rostami, J., Keller, E. (2017). Application of new void detection algorithm for analysis of feed pressure and rotation pressure of roof bolters. International Journal of Mining Science and Technology. 27 (1): 77-81.
[16]
Rostami, J., Kahraman, S., Naeimipour, A., Collins, C. (2015). Rock characterization while drilling and application of roof bolter drilling data for evaluation of ground conditions. Journal of Rock Mechanics and Geotechnical Engineering, 7 (3): 273-281.
[17]
Liu, S., Y. Luo, and H. Jia. (2018). Energy response characteristics of rock interface under drilling of roof anchorage borehole in coal roadway. Journal of China University Mining Technology. 47 (1), 88-96.
[18]
Song, Q., Jiang, H., Song, Q., Zhao, X., Wu, X. (2017). Combination of minimum enclosing balls classifier with SVM in coal-rock recognition. Plos One, 12 (9), e0184834.
[19]
Liu, C., X. Zheng, A. Arif., and M. Xu. (2019). Measurement and analysis of penetration rate and vibration on a roof bolter for identification rock interface of roadway roof, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.
[20]
Dong, S., Wang, Z., Zeng, L. (2016). Lithology identification using kernel Fisher discriminant analysis with well logs. Journal of Petroleum Science & Engineering. 143, 95-102.
[21]
Yahiaoui, M., Paris, J. Y., Delbé, K., Denape, J., Gerbaud, L., Dourfaye, A. (2016). Independent analyses of cutting and friction forces applied on a single polycrystalline diamond compact cutter. International Journal of Rock Mechanics & Mining Sences. 85, 20-26.
Browse journals by subject